ISO 8434-2 PDF

ISO INTERNATIONAL. STANDARD. ISO. Second edition. Metallic tube connections for fluid power and general use —. Part 2. 37° flare couplings to ISO comprise a body. (1), pressure sleeve (2) and securing nut (3). By exchanging the pressure sleeve, the same coupling can be. The SAE J/ISO standard outlines the general and dimensional requirements for the design and performance of 37° flaring fittings, suitable to be used.

Author: Nizragore Fenriktilar
Country: Philippines
Language: English (Spanish)
Genre: Career
Published (Last): 3 November 2005
Pages: 129
PDF File Size: 20.39 Mb
ePub File Size: 18.34 Mb
ISBN: 284-3-70065-255-9
Downloads: 6225
Price: Free* [*Free Regsitration Required]
Uploader: Vudole

ISO consists of the following parts, under the general title Metallic tube connections for fluid power and general use: Testing of three samples to confirm that the specified connection s is are capable of withstanding a minimum of four times the working pressure without failure.

Test methods for threaded hydraulic fluid power connections Annex A forms an integral part ios this part of ISO IFS PACsecure is a standard that was designed for managing quality and safety related to product packaging. Testing of three samples to confirm that the specified connection s meet s or exceed s a ratio of 2: Annex A forms an integral part of this part of ISO Metallic tube connections for fluid power and general use – Part 5: Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

Cyclic endurance test results: A Applicable tests for various fitting and stud end standards. Metallic tube connections for fluid power.

Lso, the thread-to-nut overtorque and seal performance have been extensively tested; to change to metric threads would require an extensive test program at considerable cost without providing any functional improvement.

  DESCARGAR EL LIBRO UN GRITO DESESPERADO CARLOS CUAUHTEMOC SANCHEZ PDF

ISO consists of the following parts, under the general title Metallic tube connections for fluid power and general use: In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit.

Use the same equipment as specified in 5.

Adjustable stud torques shall be applied after being backed out one full turn from finger- tight position to test correctly the worst possible actual assembly conditions. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that isp. A new version of the Standard for Information Security. Stud ends for general use only with metal- to-metal sealing type B. To reduce the hazard of energy release, bleed air out of test specimens ixo to pressure testing.

Packaging and Packaging Materials issue 4 then became the first packaging Heavy-duty S series stud ends. Adjustable stud torques shall be applied after being backed out one full turn from finger.

Pipe fittings ISO

In general applications, a fluid may be conveyed under pressure. Adobe is a trademark of Adobe Systems Incorporated. Testing of six samples to confirm that they are capable of withstanding the overtorque qualification test when tested to the overtorque values shown in their respective standards.

Attention is drawn to the danger of burst, fine jets which can penetrate the skin and energy release of expanding gases. The distance between the port centreline and the edge of the test block shall be a minimum of 1 times the port diameter.

These test methods have been included in several International Standards, but because of uso generic application to ports, studs and tube connections for both metric and inch connections, it was agreed that a separate standard should be established. Use the same equipment as in 5. Tolerances for fasteners izo. Also in this second volume guitar or keyboard players will look in vain for chords and. This report is based on accounts to which one of the following applies:.

  MAKANSUTRA SINGAPORE 2013 PDF

Shri Sai Satcharita – Sai Charitra.

Access the full version online. Parts that pass this test may be used for other tests or in production. Use the following statement in test reports, catalogues and sales literature when electing to comply with this part of ISO Every care has been taken to ensure that the file is suitable for use by ISO member bodies.

Apply torque as specified in 5. The threads are integral to themselves, connectors of this type 84342 only to themselves and, other than having metric threads, no value in changing could be found. In accordance with Adobe’s licensing policy, this file may be printed or Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

Jic 37 0 Degree Flare Type As Per Iso 8434-2

Components must be designed to meet these requirements under varying conditions. All standards are subject to revision, and parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most jso editions of the standards indicated below. It is therefore essential that, in conducting these tests, all appropriate safety precautions are strictly adhered to.